Can I Change The Gauge Color In A 2015 Wrangler

Hither a write upwards on changing the display color for your gauge cluster. this particular one was done on 2010 limited.

before nosotros start you can literally choose any color you like..if yous want light-green,great job.....you are washed!

1 take a picture of your gauges with ignition off. take each seperate if neccessary to get a close upward of exactly where needle position is. non always correct at naught.and i dont know about yous but that plus or minus iii-4 could brand a difference on the speedometer in item.

ii remove steering column opening trim console. ii 10mm bolts and it pulls out .iv servant clips

3 remove instrument cluster finish console. 2 screws at the base. make sure to lower your tilt to the full down position. seperate the cavalcade trim past pressing in on the sides of the top piece and lifting upward.disconnect one harness plug for rear hatch and remove.

4 remove instrument cluster.four 7mm bolts and 1 harness plug and remove

5 remove plastic lens from gauge cluster. one phillips screw in the back and carefully seperate the tabs. yes i broke 1,luckily it was repairable.

ok hither is the fun function,simply be patient.

six there are several tools i have seen used to remove the dials from the gauge cluster..2 spoons,ane on each side and pry them off...some other used a fork although his was a picture and i didnt actually see it happen....i wasnt in the kitchen when i did this and then i chose to apply a hook pick.carefully use whatever tool will allow you to just become under the edge of the punch and pry it up. these are not quite every bit flimsy as i thought but yeah they volition break.

7 once all four dials have been removed there are 4 round retaining clips at each gauge..over again i used a pocket-size option to pry these out.

eight remove the plastic trim and if you are going to finish this project before driving your car,great set up the gauge assembly in a safe identify abroad from your piece of work surface area.if you plan on going somewhere you volition need to temp install this unit back in your edge..but reconnect the harness plug and the 4 screws. information technology wont starting time without this unit in the car and connected..this is essentially where your motorcar communicates all together.

nine you will need to sand away the parts of the trim where it shows green when light is behind information technology..i used moisture sand both 600 amd also 1000 grit..just have your time once again and yous must get ALL the dark-green off.i left the red every bit i wanted the max and high levels to be different...u can likewise make these any color y'all choose..double check and triple check to ensure that all of the dark-green is gone..

i besides used a very sharp razor blade or an exacto would work also to cut out the green display screen in front end of the info heart..then i cleaned edges with a dremil. if you lot are unsure of your skills with a dremil..dont use it! it is very piece of cake to have abroad to much material..

10 tape off the parts of the trim u desire to proceed clear or reddish or i believe there are a few that are yellowish leds on the actual board of approximate cluster..if you want to modify the colour of the yellow yous will need to change the actual leds on the board..if you dont recall u can or question your ability at all to practise this..DONT Practise IT! information technology volition crave a steady paw and a proficient soldering iron with the right tip and the correct heat level..

11 so now you need to pick your colour..or colors...if light-green is your choice and you have completed steps up to this point..well then you lot are an idiot and probably need assistance tying your shoes in the forenoon..ok ok im jk... in that location are two options you can apply to get your colour..i used both.. first u can get lighting gels which are used for stage lighting and come up in a variety pack. i purchased one pack of similar 15 dissimilar colors. they are 10x10 sheets and i got this pack at guitar middle or u can guild online..also you can apply testers transparent spray enamel..they have at hobby store but limited in colors just the basics are certainly in that location..i tried using just the gels at first but any type of adhesive i used would remove the gel color and information technology looked like crap..simply the color from gels in my opinion is much deeper and ameliorate than the testers enamel..note :the gels can exist secured with hot glue but in the example of the gauges you will notice you are express on space and if the gum oozes out the front end its going to look like crap...then my solution was to spray two coats of the testers enamel and on the third coat literally while paint was even so wet i layed the gels i had cut to fit right into the wet enamelit actually worked quite well and the ii unlike sources together gave me a squeamish shade of bluish...let it dry completely and peal your masking tape. the brandish you cut out in front of the data screen i just cutting an oversized gel and hot glued it backside the trim..u have plenty of room to use hot glue here.

basically yous are fix to reassemble...just make sure all your colour edges are good..a couple colour changes from blue to red are extremely close and so i did trim a scrap with a very sharp blade.. merely opposite your removal process and brand certain to set your gauge needles exacty where they were ..refer to your pictures .

promise this helps someone..its actually non that difficult..and i spent i think about 30 bucks on whole projection..

Source: https://www.fordedgeforum.com/topic/19813-how-to-change-gauge-cluster-lighting-color/

Posted by: ortegabeent1988.blogspot.com

Share this post